Corrosiveness of Different Types of Water


Technischer Bericht, 2013
19 Seiten, Note: A

Leseprobe

Inhalt

1. Introduction
1.1 Objectives/Aims
1.2 Methods

2. Experiment Layout
2.1 Synthetic seawater – chemical composition
2.2 Mineral water – chemical composition
2.3 CO2Water – chemical composition

3. Visual Observations
3.1 Synthetic Seawater
3.2 Mineral Water
3.3 Mineral Water (CO2added)

4. Discussion
4.1 Corrosion of Iron
4.1.1. Rust
4.1.2. Temperature Effect
4.1.3. pH Effect
4.2 CO2Dissolved in water
4.2.1. CO2corrosion mechanism
4.2.2. pH Effect
4.2.3. Temperature Effect

5. Conclusion

6. References

7. Annexes

List of Figures

Figure 1 – Synthetic Seawater

Figure 2 – Mineral water picture

Figure 3 – Sparkling water picture

Figure 4 – Iron nail immersed in synthetic seawater

Figure 5 – Iron nail immersed in mineral water

Figure 6 – Iron nail immersed in sparkling water

Figure 7 – Corrosion of iron in aerated water

List of Tables

Table 1 – Synthetic water chemical composition

Table 2 – Mineral water chemical composition

Table 3 – Sparkling water chemical composition

List of graphs

Graph 1 - Effect of pH on the corrosion rate of iron

Graph 2 – Pourbaix diagram of iron

1. Introduction

Corrosion of iron nails was analyzed through an observation experiment carried out in three different types of water to compare the difference in corrosiveness of some commercial drinking waters (mineral water, i.e. no gas, and sparkling water, i.e. with gas) and some synthetic seawater. The length period of observations was approximately 25 days.

Ph strip papers were used to measure the level of ph in the three different types of water. The frequency of ph measurement was every 3 to 4 days. Room temperature was logged and recorded every time ph measurement was taken. Details of the logbook table are available in the annex I.

1.1. Objectives

The aim of this report is to describe the corrosion of iron nails under stagnant water conditions. Observations, deductions and conclusions will be further detailed throughout the report.

1.2. Methodology

The methodology adopted to carry out this experiment, was through a combination of visual observations, supplemented by further research available on several studies carried out on corrosion phenomena.

2. Experiment layout

For this experiment 3 iron nails of 110mm x 2.5mm were polished with dry fine emery paper until nice and shiny. Two commercial drinking water (mineral water and sparkling water) and synthetic seawater were used as the aqueous environment. The commercial drinking waters were purchased at local supermarkets and the synthetic seawater was made via coursework Alternative B explanation.

2.1. Synthetic Seawater

Three table-spoonfuls of ordinary culinary salt dissolved in 1.3 litres of tap water on jug jar were used to make the synthetic seawater.

Due to lack of available equipment to measure the chemical composition of artificial seawater, the information shown on the table 1 below was taken from the work carried out by Kester et al.

Table 1 – Synthetic seawater chemical composition

Abbildung in dieser Leseprobe nicht enthalten

2.2. Mineral Water

The mineral water used for this experiment was bought at KERO supermarket. The brand name is Agua Perla, see figure 2. The chemical composition is shown on the table 2 as below.

Table 2 – Mineral water chemical composition

Abbildung in dieser Leseprobe nicht enthalten

Abbildung in dieser Leseprobe nicht enthalten

Figure 2 - Mineral water (Purchased at supermarket KERO)

2.3. Sparkling water (CO2 added)

The mineral water used for this experiment was bought at KERO supermarket. The brand name is FRIZE, see figure 3. The chemical composition is shown on the table 3 as below.

Table 3 – Sparkling water chemical composition

Abbildung in dieser Leseprobe nicht enthalten

Abbildung in dieser Leseprobe nicht enthalten

Figure 3 - Sparkling water – CO2added (Purchased at supermarket KERO)

3. Visual Observations

Throughout the length period of the experiment the following visual observations were made and recorded as illustrated on the following sections.

[...]

Ende der Leseprobe aus 19 Seiten

Details

Titel
Corrosiveness of Different Types of Water
Hochschule
Robert Gordon University Aberdeen
Veranstaltung
Master of Science in Oil and Gas Engineering
Note
A
Autor
Jahr
2013
Seiten
19
Katalognummer
V269623
ISBN (eBook)
9783656608042
ISBN (Buch)
9783656608066
Dateigröße
1481 KB
Sprache
Englisch
Anmerkungen
"A thoroughly professional job. Well done."
Schlagworte
corrosiveness, Iron nails, CO2 water
Arbeit zitieren
Ataliba Miguel (Autor), 2013, Corrosiveness of Different Types of Water, München, GRIN Verlag, https://www.grin.com/document/269623

Kommentare

  • Noch keine Kommentare.
Im eBook lesen
Titel: Corrosiveness of Different Types of Water


Ihre Arbeit hochladen

Ihre Hausarbeit / Abschlussarbeit:

- Publikation als eBook und Buch
- Hohes Honorar auf die Verkäufe
- Für Sie komplett kostenlos – mit ISBN
- Es dauert nur 5 Minuten
- Jede Arbeit findet Leser

Kostenlos Autor werden