An internal arc test is not a mandatory test. It is a consumer premises test. It should be done on the terminal box, panel, enclosure, etc. Overpressure at internal arc, inside the penal, may be a danger for the worker working inside the field. compact substation in the public area must have to be arc proof.
In this thesis report, in the beginning, the internal arc phenomena are discussed. Thereafter the internal arc test condition and their standards are given.
In the middle part of the thesis, the analytical method is given and its failure is discussed and the limitation is of the old method is clearly shown with taking practical data at calculation data.
The internal arc test is very expansive in the real working field and may danger sometimes because of loss of equipment during the test. although it is consumer selection to decide the level and location of the short circuit. It is always a risky test.
In this thesis, the computer simulation method using Finite Volume Method (FVM) for simulation of the internal arc test with following all testing standards with selecting particular assembly is modeled. The electromagnetic and fluid combined analysis is presented to a detailed plasma arc. The MHD equation is derived and solved at the end using ANSYS software.
Table of Contents
1 Introduction
1.1 Electrical arc Phenomenon
1.2 The Internal Arc process
1.2.1 Phase 1.the compression phase
1.2.2 Phase 2.the expansion phase
1.2.3 Phase 3.the emission phase
1.2.4 Phase 4.the thermal phase
1.3 Internal arc
1.4 Arc fault
1.5 Arc in Vacuum
1.5.1 Early Particle Breakdown Theories
1.5.2 Post Arc Environment
1.6 Internal Arc Test
1.6.1 General
1.6.2 Test Condition
1.6.3 Arrangement For The Equipment
1.6.4 Test producer
1.6.5 Criteria to pass the test
1.6.6 Test report
1.6.7 Transferability of test results
1.7 Physical Influences ( Pressure Rise, Gas Flow And Thermal Effects).
1.7.1 supply circuit
1.7.2 Arrangements of indicator
2 Method of Internal Arc Test and Reference Standard
2.1 IEC 61641
2.2 Terms And Definition
2.2.1 Permissible Current Under Arcing Condition
2.2.2 Permissible Arc Duration
2.2.3 Permissible Conditional Short Circuit Current Under Arcing Condition
2.2.4 Arc
2.2.5 Personal Protection Under Arcing Condition
2.2.6 ASSEMBLY Protection under arcing conditions
2.2.7 Arc Free Zone
2.2.8 Arc Proof Zone
2.2.9 Arc Proof Assembly
2.3 Assembly Characteristics Under Arcing Condition
2.4 Testing
2.4.1 General
2.4.2 Voltage
2.4.3 Current
2.4.4 Frequency
2.5 Test Producer
2.5.1 Arc Ignition
2.5.2 Assessment Of The Test
2.6 Test report
3 Literature Survey
3.1 Phase 1
3.2 Phase 2
3.3 phase3
4 Finite element Method (FEM)/finite volume method (FVM)
4.1 Introduction
4.1.1 Basic concept
4.2 Why Finite Element Method
4.3 Application of FEM in Engineering
4.4 A Brief history of FEM
4.5 Procedure of FEM
4.5.1 Computer Implementation
4.5.2 Available commercial FEM Software Package
5 Model for simulation work
5.1 model specification
5.2 methodology adopt for simulation work
6 Research paper Publication:”Electromagnetic Model of an Arc” published in IJoART
6.1 ABSTRACT
6.2 Introduction
6.3 MHD EQUATION
6.4 ELECTROMAGNETIC MODEL
6.4.1 Model geometry
6.4.2 The simulations inputs and test data
6.5 SIMULATION RESULTS
6.5.1 Time varying j, E and w
6.5.2 Transient behavior:
6.6 ANALYSES OF THE SIMULATION
6.7 CONCLUSION
6.8 ACKNOWLEDGMENTS
6.9 REFERENCES
7 Pressure estimation using CFD Method
7.1 Model developed in Pro-engineer
7.1.1 Dimensions
7.1.2 materials
7.1.3 Properties of materials
7.2 Transient electromagnetic analysis in Maxwell 15.0 to Copper losses,Energy and I2 losses
7.3 Transfer Maxwell Data to Fluent
7.4 SOME CHARACTERISTICS OF PRESSURE
7.5 Thermodynamics:Enthalpy, Entropy & Gibbs Free Energy
7.5.1 State Functions
7.5.2 Enthalpy (Heats) of Reaction
7.5.3 Entropy
7.5.4 Qualitative ”Rules” About Entropy:
7.6 Gibb’s Free Energy
7.7 Pressure Estimation
7.7.1 Computational Fluid Dynamics Method
7.8 pressure Estimation using CFD
8 Results and Conclusion
9 conclusion
Research Objectives and Themes
The primary research objective is to estimate and analyze the internal pressure development during an Internal Arc Test in electrical switchgear. The study utilizes computer simulation techniques, specifically Finite Volume Method (FVM) and Finite Element Method (FEM), to overcome the limitations of physical testing, which often fails to capture comprehensive data such as temperature, stress, and pressure distribution within the enclosure. By modeling the electrical and fluid dynamics, the work seeks to provide a robust method for predicting the performance of switchgear under arcing fault conditions and to validate these simulations against experimental data.
- Internal Arc Phenomena and Arc Fault Dynamics
- Computational Fluid Dynamics (CFD) for Pressure Estimation
- Electromagnetic Analysis of Arcing faults using Maxwell
- Integration of Multiphysics simulations (ANSYS and Fluent)
- Validation of simulation models against practical test results
Excerpt from the Book
1.1 Electrical arc Phenomenon
The electrical arc is incandesced gas column physically,with approximately straight trajectory between two electrodes (anode and cathode)and temperature around 6000 to 10000 0C and because of very high temperature metallic contact surface is also incandesced and due to such the cross section of the arc near contact is reduced and it is observed near both anode and cathode and this way total three region is created.
Summary of Chapters
1 Introduction: Provides an overview of the electrical arc phenomenon, its phases, and the requirements for internal arc testing in switchgear.
2 Method of Internal Arc Test and Reference Standard: Details the standards (IEC 61641) and definitions required for conducting and assessing internal arc tests.
3 Literature Survey: Reviews existing research and methodologies concerning arc simulation and pressure estimation techniques.
4 Finite element Method (FEM)/finite volume method (FVM): Explains the theoretical basis and computational procedures for using Finite Element and Finite Volume methods in engineering.
5 Model for simulation work: Describes the design specifications and setup of the simulation model developed in Pro-engineer.
6 Research paper Publication:”Electromagnetic Model of an Arc” published in IJoART: Discusses the electromagnetic modeling of an electric arc and analyzes the impact of magnetic fields on arc resistance.
7 Pressure estimation using CFD Method: Documents the implementation of CFD analysis to estimate pressure rise within an enclosure during an arc fault.
8 Results and Conclusion: Compares simulation outcomes with practical test results and validates the effectiveness of the CFD model.
9 conclusion: Summarizes the effectiveness of the proposed computational method for electrical safety analysis and short circuit testing.
Keywords
Internal Arc Test, Electrical Engineering, CFD, Finite Element Method, Pressure Estimation, Arc Fault, Switchgear, Magneto hydro dynamics, Plasma Arc, Ansys, Maxwell, Electrical Safety, Thermal Effects, Gas Flow, Simulation
Frequently Asked Questions
What is the primary focus of this project?
The project focuses on estimating and analyzing the pressure rise within switchgear enclosures during an internal arc fault using computational simulation techniques.
What are the central thematic fields covered?
The themes include electrical arc phenomena, thermodynamic behavior during faults, electromagnetic modeling, and the application of CFD for safety assessment in electrical power systems.
What is the core research question?
The research seeks to determine if computer simulation models can accurately predict pressure development during an internal arc test and provide better data visibility than practical tests alone.
Which scientific methods are employed?
The study employs the Finite Element Method (FEM) and Computational Fluid Dynamics (CFD), utilizing software tools such as ANSYS, Fluent, and Maxwell to simulate the physical behavior of arcs.
What is covered in the main section of the work?
The main sections cover the theory of arc formation, the methodology for creating simulation models in Pro-engineer, the extraction of data via transient electromagnetic analysis, and the final pressure estimation using CFD.
Which keywords best characterize this work?
The work is characterized by terms such as Internal Arc Test, CFD, Finite Element Method, Pressure Estimation, and Switchgear Safety.
How is the accuracy of the simulation validated?
The simulation results are compared against practical experimental data, showing a high degree of correlation (up to 99% accuracy in specific cases) between the predicted and actual pressure values.
What role does the "Neutral plane" play in the enclosure?
The neutral plane is identified as the height where pressure differences across the enclosure are zero, which is critical for understanding the gas flow patterns during an arc event.
How does insulation impact the pressure development?
The study compares cases with and without fiber glass insulation, noting that the presence of insulation alters arc behavior and affects the resulting pressure levels in the enclosure.
Why are standard physical tests considered challenging?
Physical tests are expensive, risky due to potential equipment damage, and often only provide mean values, whereas simulations provide detailed temperature, stress, and pressure distribution data.
- Citar trabajo
- PH.D Jigneshkumar Desai (Autor), 2013, Pressure Estimation During Internal Arc Test of Circuit Breaker, Múnich, GRIN Verlag, https://www.grin.com/document/1154427
